Using Equal Cost Multiple Path (ECMP)
By using the Equal Cost Multiple Path (ECMP) mechanism on a cluster deployment, active cluster nodes advertise the virtual server IP addresses. The cluster node which receives the advertised traffic steers the traffic to the node that must process the traffic. There can be redundant steering in spotted and partially striped virtual servers. Therefore, from NetScaler 11 onwards, spotted and partially striped virtual server IP addresses advertise the owner nodes, which reduce the redundant steering.
To use ECMP, you must first perform the following:
- Enable the required routing protocol (OSPF, RIP, BGP, or ISIS) on the cluster IP address.
- Bind the interfaces and the spotted IP address (with dynamic routing enabled) to a VLAN.
- Configure the selected routing protocol and redistribute the kernel routes on the ZebOS by using the vtysh shell.
You must perform similar configurations on the cluster IP address and on the external connecting device.
- Make sure that the licenses on the cluster support dynamic routing, otherwise ECMP does not work.
- ECMP is not supported for wildcard virtual servers since RHI needs a VIP address to advertise to a router and wildcard virtual servers do not have associated VIP addresses.
Figure 1. ECMP topology
As seen in the above figure, the ECMP router can reach the VIP address via SNIP0, SNIP1, or SNIP2.
To configure ECMP on the cluster by using the command line interface
Log on to the cluster IP address.
Enable the routing protocol.
> enable ns feature <feature>
Example: To enable the OSPF routing protocol.
> enable ns feature ospf
Add a VLAN.
> add vlan <id>
> add vlan 97
Bind the interfaces of the cluster nodes to the VLAN.
> bind vlan <id> -ifnum <interface_name>
> bind vlan 97 -ifnum 0/1/2 1/1/2 2/1/2
Add a spotted SNIP address for each node and enable dynamic routing on it.
> add ns ip <SNIP> <netmask> -ownerNode <positive_integer> -dynamicRouting ENABLED
> add ns ip 184.108.40.206 255.0.0.0 -ownerNode 0 -dynamicRouting ENABLED -type SNIP > add ns ip 220.127.116.11 255.0.0.0 -ownerNode 1 -dynamicRouting ENABLED -type SNIP > add ns ip 18.104.22.168 255.0.0.0 -ownerNode 2 -dynamicRouting ENABLED -type SNIP
Bind one of the spotted SNIP addresses to the VLAN. When you bind one spotted SNIP address to a VLAN, all other spotted SNIP addresses defined on the cluster in that subnet are automatically bound to the VLAN.
> bind vlan <id> -IPAddress <SNIP> <netmask>
> bind vlan 97 -ipAddress 22.214.171.124 255.0.0.0
You can use NSIP addresses of the cluster nodes instead of adding SNIP addresses. If so, you do not have to perform steps 3 - 6.
Configure the routing protocol on ZebOS using vtysh shell.
To configure OSPF routing protocol on node IDs 0, 1, and 2.
> vtysh ! interface vlan97 ! router ospf owner-node 0 ospf router-id 126.96.36.199 exit-owner-node owner-node 1 ospf router-id 188.8.131.52 exit-owner-node owner-node 2 ospf router-id 184.108.40.206 exit-owner-node redistribute kernel network 220.127.116.11/8 area 0 !
For VIP addresses to be advertised, RHI setting must done by using the vserverRHILevel parameter as follows:
add ns ip <IPAddress> <netmask> -type VIP -vserverRHILevel <vserverRHILevel>
For OSPF specific RHI settings, there are additional settings that can be done as follows:
add ns ip <IPAddress> <netmask> -type VIP -ospfLSAType ( TYPE1 | TYPE5 ) -ospfArea <positive_integer>
Use the add ns ip6 command to perform the above commands on IPv6 addresses.
Configure ECMP on the external switch. The following sample configurations are provided for the Cisco® Nexus 7000 C7010 Release 5.2(1) switch. Similar configurations must be performed on other switches.
//For OSPF (IPv4 addresses) Global config: Configure terminal feature ospf Interface config: Configure terminal interface Vlan10 no shutdown ip address 18.104.22.168/8 Configure terminal router ospf 1 network 22.214.171.124/8 area 0.0.0.0 --------------------------------- //For OSPFv3 (IPv6 addresses) Global config: Configure terminal feature ospfv3 Configure terminal interface Vlan10 no shutdown ipv6 address use-link-local-only ipv6 router ospfv3 1 area 0.0.0.0 Configure terminal router ospfv3 1
Router monitoring cluster nodes in ECMP deployment
In a cluster setup, on an owner node that has a spotted SNIP address configuration, you can now disable the ownerDownResponse option. By default, the option is enabled, allowing the node to respond to an ICMP/ARP/ICMP6/ND6 request coming from the upstream router. You can now disable this option to allow the router to monitor if a cluster node is active or inactive. When the router sends a request, if the option is disabled, it identifies the owner node to be inactive and unavailable for traffic distribution.
To configure ECMP for static routes traffic distribution by using the command line interface
add ns ip <ipddress> <netmask> -ownernode <node-id> –ownerDownResponse disable