ADC

Use Case 2 – Non-Jumbo to Jumbo Setup

Consider an example of a regular to jumbo setup in which load balancing virtual server LBVS-1, configured on a NetScaler appliance NS1, is used to load balance traffic across servers S1 and S2. The connection between client CL1 and NS1 supports regular frames, and the connection between NS1 and the servers supports jumbo frames.

Interface 10/1 of NS1 receives or sends traffic from or to client CL1. Interface 10/2 of NS1 receives or sends traffic from or to server S1 or S2.

Interfaces 10/1 and 10/2 of NS1 are part of VLAN 10 and VLAN 20, respectively. For supporting only regular frames between CL1 and NS1, the MTU is set to the default value of 1500 for both interface 10/1 and VLAN 10

For supporting jumbo frames between NS1 and the servers, the MTU is set to 9000 for interface 10/2 and VLAN 20. Servers and all other network devices between NS1 and the servers are also configured for supporting jumbo frames.

Since HTTP traffic is based on TCP, MSSs are set accordingly at each end point for supporting jumbo frames.

  • For supporting jumbo frames for the connection between a SNIP address of NS1 and S1 or S2, the MSS on NS1 is set accordingly in a custom TCP profile, which is bound to the services (SVC-S1 and SVC-S1 ) representing S1 and S2 on NS1.
  • For supporting only regular frames for the connection between CL1 and virtual server LBVS-1 of NS1, default TCP profile nstcp_default_profile is used that is by default bound to LBVS-1 and has the MSS set to the default value of 1460.

jumbo uc2

The following table lists the settings used in this example.

Entity Name Details
IP address of client CL1 192.0.2.10
IP address of servers S1 198.51.100.19
S2
SNIP address on NS1 198.51.100.18
MTU specified for interfaces and VLANs on NS1 10/1 1500
10/2
VLAN 10
VLAN 20
Default TCP profile nstcp_default_profile MSS:1460
Custom TCP profile NS1-SERVERS-JUMBO MSS: 8960
Services on NS1 representing servers SVC-S1 IP address: 198.51.100.19, Protocol: HTTP, Port: 80, TCP profile: NS1-SERVERS-JUMBO (MSS: 8960)
SVC-S2
Load balancing virtual server on VLAN 10 LBVS-1 IP address = 203.0.113.15, Protocol: HTTP, Port:80, Bound services: SVC-S1, SVC-S2, TCP Profile: nstcp_default_profile (MSS:1460)

Following is the traffic flow of CL1’s request to S1 in this example:

  1. Client CL1 creates a 200-byte HTTP request to send to virtual server LBVS-1 of NS1.

  2. CL1 opens a connection to LBVS-1 of NS1. CL1 and NS1 exchange their respective TCP MSS values while establishing the connection.

  3. Because NS1’s MSS is larger than the HTTP request, CL1 sends the request data in a single IP packet to NS1.

    Size of the request packet = [IP Header + TCP Header + TCP Request] = [20 + 20 + 200] = 240

  4. NS1 receives the request packet at interface 10/1 and then processes the HTTP request data in the packet.

  5. LBVS-1’s load balancing algorithm selects server S1, and NS1 opens a connection between one of its SNIP addresses and S1. NS1 and CL1 exchange their respective TCP MSS values while establishing the connection.

  6. Because S1’s MSS is larger than the HTTP request, NS1 sends the request data in a single IP packet to S1.

    Size of the request packet = [IP Header + TCP Header + [TCP Request] = [20 + 20 + 200] = 240

Following is the traffic flow of S1’s response to CL1 in this example:

  1. Server S1 creates an 18000-byte HTTP response to send to the SNIP address of NS1.
  2. S1 segments the response data into multiples of NS1’s MSS and sends these segments in IP packets to NS1. These IP packets are sourced from S1’s IP address and destined to the SNIP address of NS1.

    • Size of the first two packet = [IP Header + TCP Header + (TCP segment=NS1’s MSS size)] = [20 + 20 + 8960] = 9000
    • Size of the last packet = [IP Header + TCP Header + (remaining TCP segment)] = [20 + 20 + 80] = 120
  3. NS1 receives the response packets at interface 10/2.
  4. From these IP packets, NS1 assembles all the TCP segments to form the HTTP response data of 18000 bytes. NS1 processes this response.
  5. NS1 segments the response data into multiples of CL1’s MSS and sends these segments in IP packets, from interface 10/1, to CL1. These IP packets are sourced from LBVS-1’s IP address and destined to CL1’s IP address.

    • Size of all packets except the last one = [IP Header + TCP Header + (TCP payload=CL1’s MSS size)] = [20 + 20 + 1460] = 1500
    • Size of the last packet = [IP Header + TCP Header + (remaining TCP segment)] = [20 + 20 + 480] = 520

Configuration Tasks

The following table list the tasks, NetScaler commands, and examples for creating the required configuration on the NetScaler appliance.

Tasks CLI Syntax Examples
Set the MTU of the desired interfaces for supporting jumbo frames set interface -mtu , show interface set int 10/1 -mtu 1500 set int 10/2 -mtu 9000
Create VLANs and set the MTU of the desired VLANs for supporting jumbo frames add vlan -mtu , show vlan add vlan 10 -mtu 1500 add vlan 20 -mtu 9000
Bind interfaces to VLANs bind vlan -ifnum , show vlan bind vlan 10 -ifnum 10/1 bind vlan 20 -ifnum 10/2
Add a SNIP address add ns ip -type SNIP, show ns ip add ns ip 198.51.100.18 255.255.255.0 -type SNIP
Create services representing HTTP servers add service HTTP , show service add service SVC-S1 198.51.100.19 http 80, add service SVC-S2 198.51.100.20 http 80
Create HTTP load balancing virtual servers and bind the services to it add lb vserver HTTP , bind lb vserver , show lb vserver add lb vserver LBVS-1 http 203.0.113.15 80, bind lb vserver LBVS-1 SVC-S1, bind lb vserver LBVS-1 SVC-S2
Create a custom TCP profile and set its MSS for supporting jumbo frames add tcpProfile -mss , show tcpProfile add tcpprofile NS1-SERVERS-JUMBO -mss 8960
Bind the custom TCP profile to the desired services set service -tcpProfileName , show service set service SVC-S1 -tcpProfileName NS1-SERVERS-JUMBO, set service SVC-S2 -tcpProfileName NS1-SERVERS-JUMBO
Save the configuration save ns config, show ns config  
Use Case 2 – Non-Jumbo to Jumbo Setup