Prepare for installation

Before you install your new appliance, carefully unpack your appliance and make sure that all parts were delivered. Once you are satisfied that your appliance has been delivered to your expectations, verify that the location where the appliance will be installed meets temperature and power requirements and that the server cabinet or floor-to-ceiling cabinet is securely bolted to the floor and has sufficient airflow.

Note: On all appliances, the air flows from front to rear.

Only trained and qualified personnel should install, maintain, or replace the appliance, and efforts should be taken to ensure that all cautions and warnings are followed.

Unpack the appliance

The hardware accessories for your particular appliance, such as cables, adapters, and rail kit, vary depending on the hardware platform you ordered. Unpack the box that contains your new appliance on a sturdy table with plenty of space and inspect the contents.

Verify that you received the cables, adapter, and rail kits specified for your appliance.

Note

Make sure that a power outlet is available for each cable.

If the kit that you received does not fit your rack, contact your Citrix sales representative to order the appropriate kit.

Transceiver modules are sold separately. Contact your Citrix sales representative to order transceiver modules for your appliance. Only transceivers supplied by Citrix are supported on the appliance. Important

For Brazilian customers, Citrix does not ship a power cable. Use a cable that conforms to the ABNT NBR 14136:2002 standard.

In addition to the items included in the box with your new appliance, you will need the following items to complete the installation and initial configuration process.

  • Ethernet cables for each additional Ethernet port that you will connect to your network.
  • One available Ethernet port on your network switch or hub for each Citrix ADC Ethernet port you want to connect to your network.
  • A computer to serve as a management workstation.

Prepare the site and rack

There are specific site and rack requirements for the Citrix ADC appliance. You must make sure that adequate environmental control and power density are available. Racks must be bolted to the ground, have sufficient airflow, and have adequate power and network connections. Preparing the site and rack are important steps in the installation process and help ensure a smooth installation.

Site requirements

The appliance should be installed in a server room or server cabinet with the following features:

  • Environment control

    An air conditioner, preferably a dedicated computer room air conditioner (CRAC), capable of maintaining the cabinet or server room at a temperature of no more than 27 degrees C/80.6 degrees F at altitudes of up to 2100 m/7000 ft, or 18 degrees C/64.4 degrees F at higher altitudes, a humidity level no greater than 45 percent, and a dust-free environment.

  • Power density

    Wiring capable of handling at least 4,000 watts per rack unit in addition to power needs for the CRAC.

Rack requirements

The rack on which you install your appliance should meet the following criteria:

  • Rack characteristics:

    Racks should be either integrated into a purpose-designed server cabinet or be the floor-to-ceiling type, bolted down at both top and bottom to ensure stability. If you have a cabinet, it should be installed perpendicular to a load-bearing wall for stability and sufficient airflow. If you have a server room, your racks should be installed in rows spaced at least 1 meter/3 feet apart for sufficient airflow. Your rack must allow your IT personnel unfettered access to the front and back of each server and to all power and network connections.

  • Power connections:

    At minimum, two standard power outlets per unit.

  • Network connections:

    At minimum, four Ethernet connection s per rack unit.

  • Space requirements:

    One empty rack unit for the Citrix ADC MPX 5500, MPX 5550/5650, MPX 5901/5905/5910, MPX 7500/9500, T1010, MPX 8005/8015/8200/8400/8600/8800, and MPX 8905/8910/8920/8930 appliances, and two consecutive empty rack units for all other appliance models.

Note: You can order the following rail kits separately.

  • Compact 4-post rail kit, which fits racks of 23 to 33 inches.
  • 2-post rail kit, which fits 2-post racks.

Important:

See Safety, cautions, warnings, and other information for detailed electrical, appliance, and rack safety precautions.