-
Getting Started with Citrix NetScaler
-
Deploy a Citrix NetScaler VPX instance
-
Install a Citrix NetScaler VPX instance on Microsoft Hyper-V servers
-
Install a NetScaler VPX instance on Linux-KVM platform
-
Prerequisites for Installing NetScaler VPX Virtual Appliances on Linux-KVM Platform
-
Provisioning the NetScaler Virtual Appliance by using OpenStack
-
Provisioning the NetScaler Virtual Appliance by using the Virtual Machine Manager
-
Configuring NetScaler Virtual Appliances to Use SR-IOV Network Interface
-
Configuring NetScaler Virtual Appliances to use PCI Passthrough Network Interface
-
Provisioning the NetScaler Virtual Appliance by using the virsh Program
-
-
Deploying NetScaler VPX Instances on AWS
-
Upgrade and downgrade a NetScaler appliance
-
-
-
-
-
-
Overriding Static Proximity Behavior by Configuring Preferred Locations
-
Example of a Complete Parent-Child Configuration Using the Metrics Exchange Protocol
-
Configuring Global Server Load Balancing for DNS Queries with NAPTR records
-
Using the EDNS0 Client Subnet Option for Global Server Load Balancing
-
-
Persistence and persistent connections
-
Advanced load balancing settings
-
Gradually stepping up the load on a new service with virtual server–level slow start
-
Protect applications on protected servers against traffic surges
-
Use source IP address of the client when connecting to the server
-
Set a limit on number of requests per connection to the server
-
Configure automatic state transition based on percentage health of bound services
-
-
Use case 2: Configure rule based persistence based on a name-value pair in a TCP byte stream
-
Use case 3: Configure load balancing in direct server return mode
-
Use case 6: Configure load balancing in DSR mode for IPv6 networks by using the TOS field
-
Use case 7: Configure load balancing in DSR mode by using IP Over IP
-
Use case 10: Load balancing of intrusion detection system servers
-
Use case 11: Isolating network traffic using listen policies
-
Use case 14: ShareFile wizard for load balancing Citrix ShareFile
-
-
-
-
-
Configuring a CloudBridge Connector Tunnel between two Datacenters
-
Configuring CloudBridge Connector between Datacenter and AWS Cloud
-
Configuring a CloudBridge Connector Tunnel Between a Datacenter and Azure Cloud
-
Configuring CloudBridge Connector Tunnel between Datacenter and SoftLayer Enterprise Cloud
-
Configuring a CloudBridge Connector Tunnel Between a NetScaler Appliance and Cisco IOS Device
-
CloudBridge Connector Tunnel Diagnostics and Troubleshooting
This content has been machine translated dynamically.
Dieser Inhalt ist eine maschinelle Übersetzung, die dynamisch erstellt wurde. (Haftungsausschluss)
Cet article a été traduit automatiquement de manière dynamique. (Clause de non responsabilité)
Este artículo lo ha traducido una máquina de forma dinámica. (Aviso legal)
此内容已动态机器翻译。 放弃
このコンテンツは動的に機械翻訳されています。免責事項
This content has been machine translated dynamically.
This content has been machine translated dynamically.
This content has been machine translated dynamically.
This article has been machine translated.
Dieser Artikel wurde maschinell übersetzt. (Haftungsausschluss)
Ce article a été traduit automatiquement. (Clause de non responsabilité)
Este artículo ha sido traducido automáticamente. (Aviso legal)
この記事は機械翻訳されています.免責事項
이 기사는 기계 번역되었습니다.
Este artigo foi traduzido automaticamente.
这篇文章已经过机器翻译.放弃
Translation failed!
Close monitor connections
The NetScaler appliance sends probes to the services through the monitors bound to the services. By default, the monitor on the appliance and the physical server follow the complete handshake procedure even for monitor probes. However, this procedure adds overhead to the monitoring process and may not be always necessary.
For the TCP type monitor, you can configure the appliance to close a monitor-probe connection after receiving SYN-ACK from the service. To do so, set the value of the monitorConnectionClose parameter to RESET. If you want the monitor-probe connection to go through the complete procedure, set the value to FIN.
Note: The monitorConnectionClose setting is applicable only for type TCP and TCP-Default monitors.
To configure monitor-connection closure by using the command line interface:
At the command prompt, type:
set lb parameter -monitorConnectionClose <monitor_conn_close_option>
Example
set lb parameter -monitorConnectionClose RESET
To configure monitor-connection closure by using the configuration utility:
- Navigate to Traffic Management > Load Balancing > Configure Load Balancing Parameters.
- Select FIN or Reset.
Closing Monitor Connections at the Service or Service Group Level
You can also configure the appliance to close a monitor-probe connection at the service and service group level by setting the monConnectionClose parameter. If this parameter is not set, the monitor connection is closed by using the value set in the global load balancing parameters. If this parameter is set at the service or service group level, the monitor connection is closed by sending a connection termination message, with the FIN or RESET bit set, to the service or service group.
To configure monitor-connection closure at the service level by using the CLI
At the command prompt, type:
set service <service_name> -monConnectionClose ( RESET | FIN )
To configure monitor-connection closure at the service group level by using the CLI
At the command prompt, type:
set serviceGroup <service_name> -monConnectionClose ( RESET | FIN )
To configure monitor-connection closure at the service level by using the GUI
- Navigate to Traffic Management > Load Balancing > Services.
- Add or edit a service, and in Basic Settings, set the Monitoring Connection Close Bit.
To configure monitor-connection closure at the service group level by using the GUI
- Navigate to Traffic Management > Load Balancing > Service Groups.
- Add or edit a service group, and in Basic Settings, set the Monitoring Connection Close Bit.
Share
Share
This Preview product documentation is Citrix Confidential.
You agree to hold this documentation confidential pursuant to the terms of your Citrix Beta/Tech Preview Agreement.
The development, release and timing of any features or functionality described in the Preview documentation remains at our sole discretion and are subject to change without notice or consultation.
The documentation is for informational purposes only and is not a commitment, promise or legal obligation to deliver any material, code or functionality and should not be relied upon in making Citrix product purchase decisions.
If you do not agree, select Do Not Agree to exit.