-
Getting Started with Citrix NetScaler
-
Deploy a Citrix NetScaler VPX instance
-
Install a Citrix NetScaler VPX instance on Microsoft Hyper-V servers
-
Install a NetScaler VPX instance on Linux-KVM platform
-
Prerequisites for Installing NetScaler VPX Virtual Appliances on Linux-KVM Platform
-
Provisioning the NetScaler Virtual Appliance by using OpenStack
-
Provisioning the NetScaler Virtual Appliance by using the Virtual Machine Manager
-
Configuring NetScaler Virtual Appliances to Use SR-IOV Network Interface
-
Configuring NetScaler Virtual Appliances to use PCI Passthrough Network Interface
-
Provisioning the NetScaler Virtual Appliance by using the virsh Program
-
-
Deploying NetScaler VPX Instances on AWS
-
Upgrade and downgrade a NetScaler appliance
-
-
-
-
-
-
Overriding Static Proximity Behavior by Configuring Preferred Locations
-
Example of a Complete Parent-Child Configuration Using the Metrics Exchange Protocol
-
Configuring Global Server Load Balancing for DNS Queries with NAPTR records
-
Using the EDNS0 Client Subnet Option for Global Server Load Balancing
-
-
Persistence and persistent connections
-
Advanced load balancing settings
-
Gradually stepping up the load on a new service with virtual server–level slow start
-
Protect applications on protected servers against traffic surges
-
Use source IP address of the client when connecting to the server
-
Set a limit on number of requests per connection to the server
-
Configure automatic state transition based on percentage health of bound services
-
-
Use case 2: Configure rule based persistence based on a name-value pair in a TCP byte stream
-
Use case 3: Configure load balancing in direct server return mode
-
Use case 6: Configure load balancing in DSR mode for IPv6 networks by using the TOS field
-
Use case 7: Configure load balancing in DSR mode by using IP Over IP
-
Use case 10: Load balancing of intrusion detection system servers
-
Use case 11: Isolating network traffic using listen policies
-
Use case 14: ShareFile wizard for load balancing Citrix ShareFile
-
-
-
-
-
Configuring a CloudBridge Connector Tunnel between two Datacenters
-
Configuring CloudBridge Connector between Datacenter and AWS Cloud
-
Configuring a CloudBridge Connector Tunnel Between a Datacenter and Azure Cloud
-
Configuring CloudBridge Connector Tunnel between Datacenter and SoftLayer Enterprise Cloud
-
Configuring a CloudBridge Connector Tunnel Between a NetScaler Appliance and Cisco IOS Device
-
CloudBridge Connector Tunnel Diagnostics and Troubleshooting
This content has been machine translated dynamically.
Dieser Inhalt ist eine maschinelle Übersetzung, die dynamisch erstellt wurde. (Haftungsausschluss)
Cet article a été traduit automatiquement de manière dynamique. (Clause de non responsabilité)
Este artículo lo ha traducido una máquina de forma dinámica. (Aviso legal)
此内容已动态机器翻译。 放弃
このコンテンツは動的に機械翻訳されています。免責事項
This content has been machine translated dynamically.
This content has been machine translated dynamically.
This content has been machine translated dynamically.
This article has been machine translated.
Dieser Artikel wurde maschinell übersetzt. (Haftungsausschluss)
Ce article a été traduit automatiquement. (Clause de non responsabilité)
Este artículo ha sido traducido automáticamente. (Aviso legal)
この記事は機械翻訳されています.免責事項
이 기사는 기계 번역되었습니다.
Este artigo foi traduzido automaticamente.
这篇文章已经过机器翻译.放弃
Translation failed!
How to use a user monitor to check web sites
You can configure a user monitor to check for specific Web site problems that are reported by HTTP servers using specific HTTP codes. The following table lists the HTTP response codes that this user monitor expects.
HTTP response code | Meaning |
---|---|
200 - success | Probe success. |
503 - service unavailable | Probe failure. |
404 - not found | Script not found or cannot execute. |
500 - Internal server error | Internal error/resource constraints in dispatcher (out of memory, too many connections, unexpected system error, or too many processes). The service is not marked DOWN. |
400 - bad request | Error parsing HTTP request. |
502 - bad gateway | Error decoding script’s response. |
You configure the user monitor for HTTP by using the following parameters.
Parameter | Specifies |
---|---|
scriptName | The path and name of the script to execute. |
scriptArgs | The strings that are added in the POST data. They are copied to the request verbatim. |
dispatcherIP | The IP address of the dispatcher to which the probe is sent. |
dispatcherPort | The port of the dispatcher to which the probe is sent. |
localfileName | The name of a monitor script file on the local system. |
destPath | A particular location on the NetScaler appliance where the uploaded local file is stored. |
To create a user monitor to monitor HTTP, see Configuring Monitors in a Load Balancing Setup.
Share
Share
In this article
This Preview product documentation is Citrix Confidential.
You agree to hold this documentation confidential pursuant to the terms of your Citrix Beta/Tech Preview Agreement.
The development, release and timing of any features or functionality described in the Preview documentation remains at our sole discretion and are subject to change without notice or consultation.
The documentation is for informational purposes only and is not a commitment, promise or legal obligation to deliver any material, code or functionality and should not be relied upon in making Citrix product purchase decisions.
If you do not agree, select Do Not Agree to exit.