-
Getting Started with Citrix NetScaler
-
Deploy a Citrix NetScaler VPX instance
-
Install a Citrix NetScaler VPX instance on Microsoft Hyper-V servers
-
Install a NetScaler VPX instance on Linux-KVM platform
-
Prerequisites for Installing NetScaler VPX Virtual Appliances on Linux-KVM Platform
-
Provisioning the NetScaler Virtual Appliance by using OpenStack
-
Provisioning the NetScaler Virtual Appliance by using the Virtual Machine Manager
-
Configuring NetScaler Virtual Appliances to Use SR-IOV Network Interface
-
Configuring NetScaler Virtual Appliances to use PCI Passthrough Network Interface
-
Provisioning the NetScaler Virtual Appliance by using the virsh Program
-
-
Deploying NetScaler VPX Instances on AWS
-
Upgrade and downgrade a NetScaler appliance
-
-
-
-
-
-
Overriding Static Proximity Behavior by Configuring Preferred Locations
-
Example of a Complete Parent-Child Configuration Using the Metrics Exchange Protocol
-
Configuring Global Server Load Balancing for DNS Queries with NAPTR records
-
Using the EDNS0 Client Subnet Option for Global Server Load Balancing
-
-
Persistence and persistent connections
-
Advanced load balancing settings
-
Gradually stepping up the load on a new service with virtual server–level slow start
-
Protect applications on protected servers against traffic surges
-
Use source IP address of the client when connecting to the server
-
Set a limit on number of requests per connection to the server
-
Configure automatic state transition based on percentage health of bound services
-
-
Use case 2: Configure rule based persistence based on a name-value pair in a TCP byte stream
-
Use case 3: Configure load balancing in direct server return mode
-
Use case 6: Configure load balancing in DSR mode for IPv6 networks by using the TOS field
-
Use case 7: Configure load balancing in DSR mode by using IP Over IP
-
Use case 10: Load balancing of intrusion detection system servers
-
Use case 11: Isolating network traffic using listen policies
-
Use case 14: ShareFile wizard for load balancing Citrix ShareFile
-
-
-
-
-
Configuring a CloudBridge Connector Tunnel between two Datacenters
-
Configuring CloudBridge Connector between Datacenter and AWS Cloud
-
Configuring a CloudBridge Connector Tunnel Between a Datacenter and Azure Cloud
-
Configuring CloudBridge Connector Tunnel between Datacenter and SoftLayer Enterprise Cloud
-
Configuring a CloudBridge Connector Tunnel Between a NetScaler Appliance and Cisco IOS Device
-
CloudBridge Connector Tunnel Diagnostics and Troubleshooting
This content has been machine translated dynamically.
Dieser Inhalt ist eine maschinelle Übersetzung, die dynamisch erstellt wurde. (Haftungsausschluss)
Cet article a été traduit automatiquement de manière dynamique. (Clause de non responsabilité)
Este artículo lo ha traducido una máquina de forma dinámica. (Aviso legal)
此内容已动态机器翻译。 放弃
このコンテンツは動的に機械翻訳されています。免責事項
This content has been machine translated dynamically.
This content has been machine translated dynamically.
This content has been machine translated dynamically.
This article has been machine translated.
Dieser Artikel wurde maschinell übersetzt. (Haftungsausschluss)
Ce article a été traduit automatiquement. (Clause de non responsabilité)
Este artículo ha sido traducido automáticamente. (Aviso legal)
この記事は機械翻訳されています.免責事項
이 기사는 기계 번역되었습니다.
Este artigo foi traduzido automaticamente.
这篇文章已经过机器翻译.放弃
Translation failed!
Additional ADC configuration
1) Generate a key on the HSM. Use third party tools to create keys on the HSM.
2) Add an HSM key on the ADC.
Important!: The # character is not supported in a key name. If the key name include this character, the load key operation fails.
To add a Safenet HSM key by using the CLI:
At the command prompt, type:
add ssl hsmkey <KeyName> -hsmType SAFENET -serialNum <serial #> -password
where:
-keyName is the key created on the HSM by using third party tools.
-serialNum is the serial number of the partition on the HSM on which the keys are generated.
Note:
For HSM in a high availability setup, use the serial number of the high availability group.
-password is the password of the partition on which the keys are present.
To add a Safenet HSM key by using the GUI:
Navigate to Traffic Management > SSL > HSM and add an HSM key. You must specify the HSM Type as SAFENET.
3) Add a certificate-key pair on the ADC. You must first use a third party tool to generate a certificate associated with the key. Then, copy the certificate to the /nsconfig/ssl/ directory on the ADC.
Note:
The key must be an HSM key.
To add a certkey pair on the ADC by using the CLI:
At the command prompt, type:
add ssl certkey <CertkeyName> -cert <cert name> -hsmkey <KeyName>
To add a certkey pair on the ADC by using the GUI:
- Navigate to Traffic Management > SSL.
- In Getting Started, select Install Certificate (HSM) and create a certificate-key pair using an HSM key.
4) Create a virtual server and bind the certificate-key pair to this virtual server.
For information about creating a virtual server, click SSL virtual server configuration.
For information about adding a certificate-key pair, click Add or update a certificate-key pair.
For information about binding a certificate-key pair to an SSL virtual server, click Bind the certificate-key pair to the SSL virtual server.
Share
Share
In this article
This Preview product documentation is Citrix Confidential.
You agree to hold this documentation confidential pursuant to the terms of your Citrix Beta/Tech Preview Agreement.
The development, release and timing of any features or functionality described in the Preview documentation remains at our sole discretion and are subject to change without notice or consultation.
The documentation is for informational purposes only and is not a commitment, promise or legal obligation to deliver any material, code or functionality and should not be relied upon in making Citrix product purchase decisions.
If you do not agree, select Do Not Agree to exit.