Product Documentation

Configure multiple IP addresses for a Citrix ADC VPX standalone instance

This section explains how to configure a standalone Citrix ADC VPX instance with multiple IP addresses, in Azure Resource Manager (ARM). The VPX instance can have one or more NIC attached to it, and  each NIC can have one or more static or dynamic public and private IP addresses assigned to it. You can assign multiple IP addresses as NSIP, VIP, SNIP, and so on.

For more information, see the Azure documentation Assign multiple IP addresses to virtual machines using the Azure portal.

If you want to use PowerShell commands, see Configuring multiple IP addresses for a Citrix ADC VPX instance in standalone mode by using PowerShell commands.

Use case

In this use case, a standalone Citrix ADC VPX appliance is configured with a single NIC that  is connected to a virtual network (VNET). The NIC is associated with three IP configurations (ipconfig), each servers a different purpose - as shown in the table.

IPconfig Assocaited with Purpose
ipconfig1 Static public IP address; static private IP address Serves management traffic
ipconfig2 Static public IP address; static private address Serves client-side traffic
ipconfig3 Static private IP address Communicates with back-end servers

Note

IPConfig-3 is not associated with any public IP address.

Diagram: Topology

Here is the visual representation of the use case.

localized image

Note

In a multi-NIC, multi-IP Azure Citrix ADC VPX deployment, the private IP associated with the primary (first) IPConfig of the primary (first) NIC is automatically added as the management NSIP of the appliance. The remaining private IP addresses associated with IPConfigs need to be added in the VPX instance as a VIP or SNIP by using  the “add ns ip” command, according to your requirement.

Before you begin

Before you begin, create a VPX instance by following the steps given at this link:

Configure a Citrix ADC VPX standalone instance

For this use case, the NSDoc0330VM VPX instance is created.

Procedure to configure multiple IP addresses for a Citrix ADC VPX instance in standalone mode.

For  configuring multiple IP addresses for a Citrix ADC VPX appliance in standalone mode:

  1. Add IP addresses to the VM
  2. Configure Citrix ADC -owned IP addresses

Step 1: Add IP addresses to the VM

1. In the portal, click More services > type virtual machines in the filter box, and then click Virtual machines.

2. In the Virtual machines blade, click the VM you want to add IP addresses to. Click Network interfaces in the virtual machine blade that appears, and then select the network interface.

localized image

In the blade that appears for the NIC you selected, click IP configurations. The existing IP configuration that was assigned when you created the VM, ipconfig1, is displayed. For this use case, make sure the IP addresses associated with ipconfig1 are static. Next, create two more IP configurations: ipconfig2 (VIP) and ipconfig3 (SNIP).

To create additional ipconfigs, create Add.

localized image

 In the Add IP configuration window, enter a Name, specify allocation method as Static, enter an IP address (192.0.0.5 for this use case), and enable Public IP address.

Note

Before adding a static private IP address, check for IP address availability and make sure the IP address belongs to the same subnet to which the NIC is attached.

localized image

 Next, click Configure required settings to create a static public IP addresss for ipconfig2.

By default, public IPs are dynamic. To make sure that the VM always uses the same public IP address, create a static Public IP.

In the Create public IP address blade, add a Name, under Assignment click Static. And then click OK.

localized image

Note

Even when you set the allocation method to static, you cannot specify the actual IP address assigned to the public IP resource. Instead, it gets allocated from a pool of available IP addresses in the Azure location the resource is created in.

Follow the steps to add one more IP configuration for ipconfig3. Public IP is not mandatory.

localized image

Step 2: Configure Citrix ADC-owned IP addresses

Configure the Citrix ADC-owned IP addresses by using the GUI or the command “add ns ip.” For more information, see Configuring Citrix ADC-Owned IP Addresses.

You’ve now configured multiple IP addresses for a Citrix ADC VPX instance in standalone mode.

Configure multiple IP addresses for a Citrix ADC VPX standalone instance

In this article