-
Getting Started with Citrix NetScaler
-
Deploy a Citrix NetScaler VPX instance
-
Install a NetScaler VPX instance on Microsoft Hyper-V servers
-
Install a NetScaler VPX instance on Linux-KVM platform
-
Prerequisites for Installing NetScaler VPX Virtual Appliances on Linux-KVM Platform
-
Provisioning the NetScaler Virtual Appliance by using OpenStack
-
Provisioning the NetScaler Virtual Appliance by using the Virtual Machine Manager
-
Configuring NetScaler Virtual Appliances to Use SR-IOV Network Interface
-
Configuring NetScaler Virtual Appliances to use PCI Passthrough Network Interface
-
Provisioning the NetScaler Virtual Appliance by using the virsh Program
-
Provisioning the NetScaler Virtual Appliance with SR-IOV, on OpenStack
-
Configuring a NetScaler VPX Instance on KVM to Use OVS DPDK-Based Host Interfaces
-
-
Upgrade and downgrade a NetScaler appliance
-
-
-
-
-
Configure DNS resource records
-
Create SRV records for a service
-
-
Caching of EDNS0 client subnet data when the NetScaler appliance is in proxy mode
-
-
-
Persistence and persistent connections
-
Advanced load balancing settings
-
Gradually stepping up the load on a new service with virtual server–level slow start
-
Protect applications on protected servers against traffic surges
-
Use source IP address of the client when connecting to the server
-
Set a limit on number of requests per connection to the server
-
Configure automatic state transition based on percentage health of bound services
-
-
Use case 2: Configure rule based persistence based on a name-value pair in a TCP byte stream
-
Use case 3: Configure load balancing in direct server return mode
-
Use case 6: Configure load balancing in DSR mode for IPv6 networks by using the TOS field
-
Use case 7: Configure load balancing in DSR mode by using IP Over IP
-
Use case 10: Load balancing of intrusion detection system servers
-
Use case 11: Isolating network traffic using listen policies
-
Use case 14: ShareFile wizard for load balancing Citrix ShareFile
-
-
-
-
-
-
Configuring a CloudBridge Connector Tunnel between two Datacenters
-
Configuring CloudBridge Connector between Datacenter and AWS Cloud
-
Configuring a CloudBridge Connector Tunnel Between a Datacenter and Azure Cloud
-
Configuring CloudBridge Connector Tunnel between Datacenter and SoftLayer Enterprise Cloud
-
Configuring a CloudBridge Connector Tunnel Between a NetScaler Appliance and Cisco IOS Device
-
CloudBridge Connector Tunnel Diagnostics and Troubleshooting
This content has been machine translated dynamically.
Dieser Inhalt ist eine maschinelle Übersetzung, die dynamisch erstellt wurde. (Haftungsausschluss)
Cet article a été traduit automatiquement de manière dynamique. (Clause de non responsabilité)
Este artículo lo ha traducido una máquina de forma dinámica. (Aviso legal)
此内容已动态机器翻译。 放弃
このコンテンツは動的に機械翻訳されています。免責事項
This content has been machine translated dynamically.
This content has been machine translated dynamically.
This content has been machine translated dynamically.
This article has been machine translated.
Dieser Artikel wurde maschinell übersetzt. (Haftungsausschluss)
Ce article a été traduit automatiquement. (Clause de non responsabilité)
Este artículo ha sido traducido automáticamente. (Aviso legal)
この記事は機械翻訳されています.免責事項
이 기사는 기계 번역되었습니다.
Este artigo foi traduzido automaticamente.
这篇文章已经过机器翻译.放弃
Translation failed!
Create SRV records for a service
The SRV record provides information about the services available on the NetScaler appliance. An SRV record contains the following information: name of the service and the protocol, domain name, TTL, DNS class, priority of the target, weight of records with the same priority, port of the service, and host name of the service. The NetScaler chooses the SRV record that has the lowest priority setting first. If a service has multiple SRV records with the same priority, clients use the weight field to determine which host to use.
Add an SRV record by using the CLI
At the command prompt, type the following commands to add an SRV record and verify the configuration:
- add dns srvRec <domain> <target> -priority <positive_integer> -weight <positive_integer> -port <positive_integer> [-TTL <secs>]
- sh dns srvRec <domain>
Example:
> add dns srvRec _http._tcp.example.com nameserver1.com -priority 1 -weight 1 -port 80
Done
> show dns srvRec _http._tcp.example.com
1) Domain Name : _http._tcp.example.com
Target Host : nameserver1.com
Priority : 1 Weight : 1
Port : 80 TTL : 3600 secs
Done
Modify or remove an SRV record by using the CLI
- To modify an SRV record, type the
set dns srvRec
command, the name of the domain for which the SRV record is configured, the name of the target host that hosts the associated service, and the parameters to be changed, with their new values. - To remove an SRV record, type the
rm dns srvRec
command, the name of the domain for which the SRV record is configured, and the name of the target host that hosts the associated service.
Configure an SRV record by using the GUI
Navigate to Traffic Management > DNS > Records > SRV Records and create an SRV record.
Share
Share
This Preview product documentation is Citrix Confidential.
You agree to hold this documentation confidential pursuant to the terms of your Citrix Beta/Tech Preview Agreement.
The development, release and timing of any features or functionality described in the Preview documentation remains at our sole discretion and are subject to change without notice or consultation.
The documentation is for informational purposes only and is not a commitment, promise or legal obligation to deliver any material, code or functionality and should not be relied upon in making Citrix product purchase decisions.
If you do not agree, select Do Not Agree to exit.