This content has been machine translated dynamically.
Dieser Inhalt ist eine maschinelle Übersetzung, die dynamisch erstellt wurde. (Haftungsausschluss)
Cet article a été traduit automatiquement de manière dynamique. (Clause de non responsabilité)
Este artículo lo ha traducido una máquina de forma dinámica. (Aviso legal)
此内容已经过机器动态翻译。 放弃
このコンテンツは動的に機械翻訳されています。免責事項
이 콘텐츠는 동적으로 기계 번역되었습니다. 책임 부인
Este texto foi traduzido automaticamente. (Aviso legal)
Questo contenuto è stato tradotto dinamicamente con traduzione automatica.(Esclusione di responsabilità))
This article has been machine translated.
Dieser Artikel wurde maschinell übersetzt. (Haftungsausschluss)
Ce article a été traduit automatiquement. (Clause de non responsabilité)
Este artículo ha sido traducido automáticamente. (Aviso legal)
この記事は機械翻訳されています.免責事項
이 기사는 기계 번역되었습니다.책임 부인
Este artigo foi traduzido automaticamente.(Aviso legal)
这篇文章已经过机器翻译.放弃
Questo articolo è stato tradotto automaticamente.(Esclusione di responsabilità))
Translation failed!
选择部署模式
SD-WAN 4000、4100 和 5100 设备可以内联或以单臂模式部署。内联部署不需要重新配置路由器;单臂模式需要重新配置。这些平台版本提供内部端口旁路(故障到线路),以允许在设备出现故障时流量以串联模式继续流动。
部署单个 SD-WAN 4000、4100、5100 设备(或高可用性对)
独立的 SD-WAN 4000、4100、5100 设备可以部署在以下推荐模式之一:
- 内联,桥接(L2 内联)。这与标准 SD-WAN 内联部署非常相似。数据包进入一个网桥端口并退出另一个网桥端口。
- 内联,已路由。NetScaler 实例使用路由规则而不是桥接规则来确定如何转发数据包。
- 虚拟内联。这类似于 WCCP,但缺乏内置的运行状况检查。
在 L2 内联模式下,可以在 LAN 和 WAN 路由器(或 LAN-WAN 边界的其他聚合点)之间配置 SD-WAN 4000、4100、5100 版本。在单臂模式下,SD-WAN 4000、4100 或 5100 直接连接到 WAN 路由器上的专用端口。
如果 WAN 路由器端口速度不如 LAN 那么快(例如,WAN 路由器具有千兆位以太网,但 LAN 具有 10 千兆以太网时),内联模式可提供更好的性能,因为 LAN 端流量不限于路由器接口的速度。(压缩允许局域网端流量在良好的条件下比限制广域网流量快得多。)
注意事项
- 内联模式不需要对路由器进行重新配置,但在将设备投入使用时会导致服务中断。
- 单臂模式需要重新配置路由器,但不需要中断服务。
- 内联模式的性能比其他模式更高。
- 单臂模式的速度限制为所连接的路由器或交换机端口的一半。
建议
- 内联模式对于较小的 WAN 网络和更简单的数据中心来说非常方便。
共享
共享
This Preview product documentation is Cloud Software Group Confidential.
You agree to hold this documentation confidential pursuant to the terms of your Cloud Software Group Beta/Tech Preview Agreement.
The development, release and timing of any features or functionality described in the Preview documentation remains at our sole discretion and are subject to change without notice or consultation.
The documentation is for informational purposes only and is not a commitment, promise or legal obligation to deliver any material, code or functionality and should not be relied upon in making Cloud Software Group product purchase decisions.
If you do not agree, select I DO NOT AGREE to exit.