This content has been machine translated dynamically.
Dieser Inhalt ist eine maschinelle Übersetzung, die dynamisch erstellt wurde. (Haftungsausschluss)
Cet article a été traduit automatiquement de manière dynamique. (Clause de non responsabilité)
Este artículo lo ha traducido una máquina de forma dinámica. (Aviso legal)
此内容已经过机器动态翻译。 放弃
このコンテンツは動的に機械翻訳されています。免責事項
이 콘텐츠는 동적으로 기계 번역되었습니다. 책임 부인
Este texto foi traduzido automaticamente. (Aviso legal)
Questo contenuto è stato tradotto dinamicamente con traduzione automatica.(Esclusione di responsabilità))
This article has been machine translated.
Dieser Artikel wurde maschinell übersetzt. (Haftungsausschluss)
Ce article a été traduit automatiquement. (Clause de non responsabilité)
Este artículo ha sido traducido automáticamente. (Aviso legal)
この記事は機械翻訳されています.免責事項
이 기사는 기계 번역되었습니다.책임 부인
Este artigo foi traduzido automaticamente.(Aviso legal)
这篇文章已经过机器翻译.放弃
Questo articolo è stato tradotto automaticamente.(Esclusione di responsabilità))
Translation failed!
连接电缆
当设备安全地安装在机架上时,请确定应使用哪些端口。然后你就可以连接电缆了。首先连接以太网电缆和可选的控制台电缆。最后连接电源线。
警告
在安装或维修设备之前,请移除所有可能与电源或电线接触的珠宝首饰和其他金属物品。当你同时触摸有线电源或电线和接地时,任何金属物体都可能迅速升温,并可能导致烧伤、使衣服放火或将金属物体熔接到暴露的端子上。
端口
使用单个加速桥的典型安装使用三个以太网端口(主端口和 apA)和五个 IP 地址(三个在主端口的子网上,两个在 apA 的子网上)。
该设备有两个主板端口和两个(SD-WAN 400/800 和 SD-WAN 1000/2000)或三个(SD-WAN 3000)加速桥接。主端口用于初始配置。
在 SD-WAN 2000 和 3000 设备上,主板端口被标记为 “0/1” 和 “0/2”。它们分别等同于主端口和 Aux1 端口。
SD-WAN 400/800/1000 和 2000 台设备各有两对加速桥接端口。3000 设备有三对加速桥接端口。在设备上,端口 1/1 和 1/2 是加速对 A (apA) 桥接端口,端口 1/3 和 1/4 是 apB 端口,端口 1/5 和 1/6 是 apC 桥接端口。
连接以太网电缆
可以使用以太网电缆将设备连接到网络。所需的电缆类型取决于用于连接到网络的端口类型。在 10/100/1000BASE-T 端口上使用带标准 RJ-45 连接器的 5e 类或 6 类以太网电缆。
将以太网电缆连接到 10/100/1000BASE-T 端口
- 将以太网电缆一端的 RJ-45 连接器插入设备的适当端口。
- 将另一端的 RJ-45 连接器插入到目标设备中,例如路由器或交换机。
- 确认连接建立后 LED 发出琥珀色光。
可以使用控制台电缆将设备连接到可用于配置该设备的计算机或终端。连接控制台电缆之前,请配置该计算机或终端,使其支持 VT100 终端仿真、9600 波特、8 数据位、1 停止位、奇偶校验以及设置为“NONE”(无)的流控制。然后将控制台电缆的一端连接到设备上的 RS232 串行端口,将另一端连接到计算机或终端。
将控制台电缆连接到计算机或终端
- 将电缆末端的 DB-9 连接器插入控制台端口。 注意:要使用带 RJ-45 转换器的电缆,请将提供的可选转换器插入控制台端口,然后将电缆连接到其上。
- 将电缆另一端的 RJ-45 连接器插入到计算机或终端的串行端口中。
连接电源线
除非你安装了第二个电源,否则设备只有一个电源。无需使用单独的地线,因为三脚插头可提供接地功能。通过安装电源线为设备供电。
将设备连接到电源
- 将电源线的一端连接到设备后面板上的电源插座,靠近电源。
- 将电源线的另一端连接到标准 110V/220V 电源插座。
This Preview product documentation is Cloud Software Group Confidential.
You agree to hold this documentation confidential pursuant to the terms of your Cloud Software Group Beta/Tech Preview Agreement.
The development, release and timing of any features or functionality described in the Preview documentation remains at our sole discretion and are subject to change without notice or consultation.
The documentation is for informational purposes only and is not a commitment, promise or legal obligation to deliver any material, code or functionality and should not be relied upon in making Cloud Software Group product purchase decisions.
If you do not agree, select I DO NOT AGREE to exit.