Citrix SD-WAN WANOP

Diagnostics

This section provides diagnostic tools to identify network issues in your SD-WAN WANOP network and troubleshoot them. You can also obtain system log files, system information, and other necessary details that assist the Citrix SD-WAN Support team in diagnosing and resolving network issues.

Following are the Diagnostics tool available in SD-WAN WANOP:

  • Tracing
  • Packet Analyzer
  • Bypass Card Test
  • Retrieve Course
  • Line Tester
  • Ping
  • Traceroute
  • System Info
  • Diagnostic Data

localized image

Tracing

The Tracing tool is used to watch the packets flowing over the SD-WAN WANOP network. It can open each packet and identify the protocol used, the IP address of the source and destination, and other payload information. This information is used by Citrix Support team to find the root cause of network issues.

You can choose to trace Packet Headers Only or Packet Headers and Payload. You can choose the module to trace and specify if the tracing should be deployment specific or system specific.

Click Start Tracing, the appliance begins to trace the packets. The results are packaged into a ZIP archive when you click Stop Tracing. This archive can be downloaded onto your computer, using the Retrieve File option. You can then forward these files to the Support team. The trace files also provide crash analysis data.

Click Analyze to view more information about the packets in Packet Analyzer tab.

localized image

You can view the time, source address, destination address, protocol, length, and payload information.

Bypass card test

You can test the fail-to-wire functionality of Ethernet interface for an appliance deployment in inline (Fail-to-wire) mode. Enter the number of seconds for the appliance to stay in bypass mode and click Start Test. During this period, the appliance is bypassed. Normal operation will resume after that.

localized image

Retrieve cores

Core files are created when the SD-WAN WANOP appliance exits abnormally or crashes. The appliance restarts automatically after a crash. In case of persistent crashes, acceleration is disabled but the management interface remains active.

You can select and retrieve the required core files that were created during the appliance crash or when the appliance behaved abnormally. The retrieved files are saved in a ZIP archive. You can share this with the support team for further analysis.

localized image

Line tester

The Line Test: SERVER function starts an iperf server on the appliance, running in TCP mode. This option can be used to verify connectivity between WANOP appliances and troubleshooting network traffic. To run iperf tests, one system (an appliance or another host) must run iperf as a server, and another must connect to it as a client.

localized image

You can use the default Line Tester Server interface and port number. Click Start Server to start an iperf server on the appliance.

localized image

The Line Test: CLIENT function starts an iperf client on the unit, running in TCP mode. You can also specify the iperf server port number and the length of the test. When the test is complete, the connection speed will be reported. Click Start Test to see the WAN and LAN traffic result.

localized image

Ping

Ping allows you to check connectivity of the network elements in your SD-WAN network. Enter the IP address of the network element and click Run Ping to see the result.

localized image

Traceroute

Traceroute allows you to record the route between your SD-WAN appliance and any other network element in your SD-WAN network or on the internet. It calculates and displays the amount of time each hop took.

localized image

System info

The System Info lists all the parameters that are not set to their defaults. This information is read-only. It is used by Support when some kind of misconfiguration is suspected. When you report a problem, you may be asked to check one or more values on this page.

It provides Non-Default Settings, Detailed Information For Adapter Primary, Detailed Information For Adapter apA.2, and Detailed Information For Adapter apA.1.

localized image

Diagnostic Data

Diagnostic Data allows you to package diagnostic data for analysis by the Citrix Support team. Select the diagnostic files required and click Start. You can then, click Retrieve File to download the zip archive, and share it with Citrix Support.

localized image

Diagnostics